All Completed Tasks

Title Detail Completed by
Assemble light table We have parts from a large work and light table. Near the back woodshop door. We need someone to assemble with screws. Not all shelves are needed. Likely will will be pushed against wall.
Lior Trestman
Thu, 03/05/2020 - 8:03pm
Setup Homing on Shapeoko CNC It seems that for whatever reason the shapeoko totally stops when it hits a limit switch. It would be preferable to be able to use those switches for homing the device. This needs investigation. I suspect this is something in the grbl config https://github.com/grbl/grbl but not certain.
Lior Trestman
Thu, 03/05/2020 - 8:03pm
Find leak in air system Our compressed air system (running through copper pipe) has a leak somewhere. By filling a spray bottle with soapy water, you can find which joint in the pipe is leaking when it makes bubbles. If you find it, please tell Lior where it is!
Lior Trestman
Thu, 03/05/2020 - 8:03pm
Laser Lens Replacements The laser lenses have gotten older. We need to replace them from time to time. Help by:
1. figure out what lens housing we have and what lenses they fit. 
2. Have JR buy any additional needed lenses. 
3. Research and secure lens with appropriate adhesive.

Lior Trestman
Thu, 03/05/2020 - 8:03pm
Build Dust Shoe or big CNC
Lior Trestman
Thu, 03/05/2020 - 8:02pm
Add dro to bridgeport
Alex Murdoch
Wed, 02/12/2020 - 8:14pm
Add backpack hooks under round table
Larry Laconi
Wed, 02/12/2020 - 4:05pm
Take out trash & recycling TRASH: Grab trash from kitchen and any other full ones from the space and empty into large black trash can. Remove bag and bring trash up to the  MakeHaven dumpster in the courtyard (BLUE, says John's Recycling/MakeHaven). Get the dumpster key from staff. Replace trash bag in large bin with a bag from the black tool chest next to the bins.
 
RECYCLING: When full (pickup is Wednesday morning): Bring the blue recycling hopper to the courtyard and leave next to MakeHaven's dumpster. 

Mark Steeves
Thu, 02/06/2020 - 7:24pm
Tune the jointer in and outfeeds The jointer beds probably need to be removed and have the dovetails cleaned, then remounted and squared. Currently they are not quite square. Talk to Lior if you're interested in working on this.
Rudy Burrard
Mon, 01/27/2020 - 10:10pm
Vacuum the woodshop The woodshop could use a good vacuuming!
Clancy Emanuel
Fri, 01/03/2020 - 4:02pm
Clean up wood scrap The wood scrap bins in the storage area have a lot of junk in them, if someone could go through, organize the wood a little bit, and throw out things that don't look useful, that would be sweet!
Max Sutter
Mon, 12/16/2019 - 1:08pm
Get webcams working on 3d printers
Andrew Suzuki
Tue, 12/03/2019 - 9:41pm
Draft Orientation Quiz for Bridgeport Mill Write a several question quiz specific to the Bridgeport
Lior Trestman
Wed, 11/27/2019 - 1:38pm
Fix Name/Date Label Maker
Michael Lerch
Fri, 11/08/2019 - 10:35pm
Figure out how to build/control tool power boxes with card system
Jessica Badowski
Tue, 11/05/2019 - 4:46pm
Get Shapeoko's computer working (OS installed) or a new computer on the shapeoko The Shapeoko needs a browser to run. Attach a happy computer or make this computer happy. Go, Shapeoko, go! 
Lior Trestman
Mon, 11/04/2019 - 12:15pm
Fix Popcorn Maker One of the two heating coils in the kettle seems to have burnt out. It will need someone with understanding of basic electronics to troubleshoot and get running at full power again.
Lior Trestman
Mon, 11/04/2019 - 12:15pm
Setup Large CNC Getting the big CNC going is long overdue. This is a big project that requires technical expertise.
Lior Trestman
Mon, 11/04/2019 - 12:15pm
Setup Large CNC Getting the big CNC going is long overdue. This is a big project that requires technical expertise.
Lior Trestman
Mon, 11/04/2019 - 12:15pm
Setup VR at front of Room We want to be able to use the VR setup at front of room. Get it setup. 3d print hangers for headset and controler on Thineverse. 
Lior Trestman
Mon, 11/04/2019 - 12:15pm
Create Ethernet cable to go to staff room computer.
Lior Trestman
Mon, 11/04/2019 - 12:14pm
Get the Gerber CNC running We have this awesome tool. Can you make it work?
Andrew Suzuki
Wed, 10/16/2019 - 2:26pm
Get Task Display Running on Monitor Copy the raspberry pi display SD card. Setup on screen to left of TV. Point to https://www.makehaven.org/task-recognition
Michael Lerch
Sun, 10/06/2019 - 1:29pm
Clean Out the Fridge Remove all materials that are not labled or are out of date.
Make Haven
Sun, 09/01/2019 - 3:47pm
Setup Tormach Get system setup in main room.
This includes computer setup, bits and test system.

Make Haven
Sun, 09/01/2019 - 2:58pm
Setup Welcome Coffee Table Paint circle area
Add welcome design
Add hooks for cups
Set up coffee making equipment

Make Haven
Sun, 09/01/2019 - 1:34pm
Get Library books organized In the green room. Then update this spreadsheet.
J.R. Logan
Sun, 09/01/2019 - 12:10pm
Get casting pot connected to compressed air Requires connection from central compressed air to pot. Talk to JR. Some fittings will need to be sourced.
J.R. Logan
Sun, 09/01/2019 - 12:10pm
Mount doorbell video screen
Make Haven
Sun, 09/01/2019 - 11:53am
Preform Laser Cutter Maintenance (laser #1) Open it up.
Refer to manual before starting.
Vacuum and clean all surface.
Inventory where replacement belts and bearings are needed. 
Test beam straight, determine impact of lenses on power and if replacements are needed.
Relay needs to JR
Reasemble laser and test.

Make Haven
Sun, 09/01/2019 - 11:53am